BW film developing - drying marks

BW film developing - drying marks

  • Yes I do.

    Votes: 625 93.8%

  • No I don't.

    Votes: 8 1.2%

  • I will one day, I promise.

    Votes: 32 4.8%

  • I tried it and won't do it again.

    Votes: 1 0.2%
  • Total voters
    666
thomasw_ said:
This is a very good old thread, thanks for resurrecting it.

First measure to take is to throw away any type of squeegee or cloth wiping device; there's no need to introduce an unnecessary physical force to your negs. Now, bear in mind, I live in an area with tap water that will leave terrible marks after drying. These are the steps I used to eliminate them as much as possible:

1. do my LFN final rinse in distilled or filtered water

2. keeping the film on the spool, use a lettuce/salad spinner to get most of the residual rinsing water off of my negs before hanging them to dry; i use a counter-balancing technique of four spools held in place by rubber elastics

3. use a drying cabinet, hanging the negs at a bit of a slant

I have eliminated drying marks or scratching with these measures.
Click to expand...

That salad spinner idea is a great one! I've thought of blowing a hair dryer at full force, on cool, through the plastic reel after the requisite shake. Might try tomorrow for the heck of it.
 
kdemas said:
That salad spinner idea is a great one! I've thought of blowing a hair dryer at full force, on cool, through the plastic reel after the requisite shake. Might try tomorrow for the heck of it.
Click to expand...

PS- Air for just a few seconds to blow off the excess water remnants.
 
Distilled water does the trick for me. My negatives have never been cleaner since I started using it.
 
No squeegee for me as well. I just use my fingers to run softly thru the film. I also use 1-2 small drop of Joy liquid dish washing soap and make sure you don't create suds or make it soapy.
 
The trick with the final washing water is to have most capillary action so that water will drain off of the surface gradually, smoothly as a continuously thinning film without leaving drops behind. A few drops of Photoflo or one spoonful of alcohol in the final washing can help; wipe off with wet fingers in one stroke down. In case of drop stains when dried, gently wipe with isopropyl alcohol.
 
I've said it before and I'll say it again: Photo Wipes (now known as Tidi Wipes or KayPees). I've used these for all roll films since 1982 and I can count on one hand the number of times I've had water marks or dust. This is more than 5000 rolls of 120 and 35mm film. I am a pig, my studio is always dusty, with cat and dog hair, dust and etc. Until this past summer I never had a drying space with a door on it. No need to ever deal with water marks or stuck on dust again.

Sprint End-Run mixed with distilled water as per the bottle instructions, I take the reel out of the solution, let it drip a moment, give it a gentle shake, pull the film off the reel, wipe once in a single motion with a half a Wipe (folded in half to make a 1" x 6" or so wad, then again around the film) held between index and middle fingers, clip the empty cassette (with the roll number with 35mm) or a wooden clothes pin to one end, a laundry hook/clothespin to the other end and hang 'em to dry. They dry faster, and completely mark & dust free. I was taught this method by Paul Krot who founded Sprint in 1982 and have never had troubles with any post processing defects on my films other than cutting them incorrectly.

I've lately been using Agfa Sistan as well, and mixing it per directions with distilled water, then adding the End Run stock to this as if it was water. I like End Run for the Anti-Static properties.

Anyone plagued by water marks can eliminate them pretty much forever by using this method.
 
pshinkaw said:
Try and do a final rinse in distilled water, just a simple pass-thru. Then dilute your wetting agent in distilled water. Your tap water probably has a high solids content.

-Paul
Click to expand...

This is also what I do, in addition to using a wetting agent. The tap water where I live has a fairly high mineral content. I've had no problems with drying marks, though, since I started using distilled water for the final wash and also for the wetting agent.
 
Bingley said:
This is also what I do, in addition to using a wetting agent. The tap water where I live has a fairly high mineral content. I've had no problems with drying marks, though, since I started using distilled water for the final wash and also for the wetting agent.
Click to expand...

Same. I only have problems with drying marks when I'm lazy and don't get distilled water for final rinse (with photo flo). I do squeegee the film between two fingers before hanging to dry and it does help, but distilled water is the best way to go.
 
Bingley said:
This is also what I do, in addition to using a wetting agent. The tap water where I live has a fairly high mineral content. I've had no problems with drying marks, though, since I started using distilled water for the final wash and also for the wetting agent.
Click to expand...

I will remember to do this method with distilled water for the final wash next time.

Thankyou for the advice!
 
I've found out that as long as you do the last wash with distilled water there is no need for Photo-Flo or any other chemicals.
 
My method...

My method...

I have a simple nonconventional method that nobody seems to agree with (probably because it's too easy...), but I get drying mark-free negatives consistently, even with the superhard Berlin tap water that I use for mixing my chemicals and for the rinses.. That is:

I don't use squeegees, sponges, nor do I wipe the film with anything.

I don't use wetting agens, HCA's, photo-flo, agepon... Just developer, stop bath, fixer, and:

After fixing, I rinse the film under running water for 10-13 minutes. Then, I pour in distilled water, rotate the film spirals a few times and let it be for a minute. Then I hang the films to dry in the bathroom - not in any special way, just top to bottom with a weight at the bottom. That's it. I reuse one liter of distilled water for 10-15 rolls of film and it costs me 1,45 euro per 5 liters, so it's not such a big cost.

This method is very unpopular and nobody ever suggests it, yet I find it works perfectly for me and is the simplest method I've ever heard of.
 
I also had probelms with drying marks and also recently found distilled water with a tiny drop of photoflow for the final rinse has made a big difference for the better.
 
I was having good results with a final rinse of distilled water.

Then I ran out of distilled water and just used tap water. I started getting water spots.

So I bought more distilled for my final rinse. I got worse water spots than ever before!

The only thing that's changed is my brand of water. Is it possible that all "distilled" water is not equal? I'm going back to the old one next time to test this theory. Also I have some Photo Flo on the way.
 
It could be there are quality differences. What I've used is not technically really 100% pure distilled water, but battery water meant for things like car batteries and for using in steam irons etc. I've used about 3 different brands and all of them have worked fine so far.

If you had this problem only once, maybe it's actually something that happened during the development phase? I had a period where all my films had nasty "blotches" in them and I finally figured it's because the quality of the tap water had changed due to a difficult winter - I even contacted the waterworks and they said the tap water was harder and more alkaline than usually during that period. So in that case I started to mix my developer into distilled water, and problem gone. I no longer live in that area and usually use tap water for the developer again..
The fixer doesn't appear to be so sensitive to water quality..
 
I decided to buy some Photo Flo because I happened to be buying printing paper at the photo store. Never realised it was so cheap, $6.50 for a 300-500ml sized bottle. I don't think I'll ever finish that bottle, the last roll I developed used about a teaspoon and it was already way too much!

Also not a single drying mark on that roll, and I didn't even bother to squeegee the negs with my fingers.
 
pshinkaw said:
Try and do a final rinse in distilled water, just a simple pass-thru. Then dilute your wetting agent in distilled water. Your tap water probably has a high solids content.

-Paul
Click to expand...

I'll second that. If I follow that advice I never have a problem - if I don't, I get drying marks about 50% of the time.
 
Well I guess 7th it ;-) Just read the rest of the comments. I just use it for the final Photo-Flo and it works perfectly. For lesser quality water, try the final rinse also as suggested.
 
You must log in or register to reply here.
Back
Top Bottom