David_Manning
Well-known
There is SO much info on the net about HC-110, but I'd like to try Tri-X pushed to 3200 using HC-110 dilution H (1+99) at either 68F or 75F.
The problem is, I can't decide on a good development time. I think my agitation sked will be constant for 30 seconds, then once every 5 minutes.
Any ideas about time? Massive Dev chart has 30C times...I don't want to go that warm.
Ideas?
The problem is, I can't decide on a good development time. I think my agitation sked will be constant for 30 seconds, then once every 5 minutes.
Any ideas about time? Massive Dev chart has 30C times...I don't want to go that warm.
Ideas?
David_Manning
Well-known
Or, as truly stand development, no agitation after the initial...
KenD
Film Shooter
I believe that Dilution H is 1+63, not 1+99. I use 5ml of syrup to 300 ml water, seems close enough.
David_Manning
Well-known
Thanks Ken. I meant dilution G.
rogue_designer
Reciprocity Failure
under with that dev (1:100, 30 sec agitation, one turn every 5 minutes at 70ish), 30 minutes is my standard for TriX at 800 (45 minutes for 1200).
I'm afraid you are in uncharted territory for me.
I'm afraid you are in uncharted territory for me.
MDenton
Established
For further advice,I suggest you pose your question on http://www.flickr.com/groups/rodinal. There are a lot of stand development 'experts' there.
David_Manning
Well-known
Thanks guys.
raytoei@gmail.com
Veteran
hi,
sorry to confuse you further:
i tried HC110 Stand development on Tri-X at iso 400, results are okay for this roll, need to do a few more to determine if this is replicable.
HC110 in 1+100 dilution, did 2 rolls in one tank, 1 for tri-x at 400 , and 1 for acros 100.
600ml water + 6ml of hc110. all in room temp water, around 28-31C
1 min agitation = 20 turns of the tank
15 mins left alone
mid-way, agitate 5 turns
15 mins left along
water stop bath -> fix -> wash
that's it.
looks okay, my notes say can reduce time further as it looks over developed.
your mileage will definitely vary.
raytoei
ps. as a rule of thumb which works for me: half of development time at 20C = development time for 30C.
sorry to confuse you further:
i tried HC110 Stand development on Tri-X at iso 400, results are okay for this roll, need to do a few more to determine if this is replicable.
HC110 in 1+100 dilution, did 2 rolls in one tank, 1 for tri-x at 400 , and 1 for acros 100.
600ml water + 6ml of hc110. all in room temp water, around 28-31C
1 min agitation = 20 turns of the tank
15 mins left alone
mid-way, agitate 5 turns
15 mins left along
water stop bath -> fix -> wash
that's it.

looks okay, my notes say can reduce time further as it looks over developed.
your mileage will definitely vary.
raytoei
ps. as a rule of thumb which works for me: half of development time at 20C = development time for 30C.
John Bragg
Well-known
You could reduce the initial agitation quite a bit and that may help tame the contrast. Try ten or fifteen seconds. ?
David_Manning
Well-known
Since the Massive Dev chart has a time for 30C, does it make sense to double the time for 20C then?
Also, will less agitation preserve highlights, ie true stand for the push to limit contrast?
Also, will less agitation preserve highlights, ie true stand for the push to limit contrast?
Share:
-
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.