sgtnikolaix
Member
Hello,
I was wondering if anyone knows anywhere that sells the leatherette/vulcanite(?) for a Zorki-C?
I tried cameraleather.com but they seem to only do it for the later models.
I was wondering if anyone knows anywhere that sells the leatherette/vulcanite(?) for a Zorki-C?
I tried cameraleather.com but they seem to only do it for the later models.
ZeissFan
Veteran
You could always buy a 9x12 sheet and cut some yourself. If you had the old leatherette, you could use this as a pattern. It's a bit tricky to do it this way, because it just is.
I had to do this for a Komaflex. No one is offering precut kits for this camera. The old rubber covering pretty much disintegrated every time I touched it.
I had to do this for a Komaflex. No one is offering precut kits for this camera. The old rubber covering pretty much disintegrated every time I touched it.
sgtnikolaix
Member
True, I never considered that! What sort of adhesive did you use to get it to stick?
Also, is vulcanite difficult to remove?
Also, is vulcanite difficult to remove?
rbiemer
Unabashed Amateur
You might want to go at it this way:
It should be fairly straight forward to get the major dimensions--height and length--by simply measuring.
The tricky part will be sorting all the other cuts.
For those, I would start with a heavy kind of paper, cut out a rectangle that will cover the body, anchor that to the body (maybe rubber cement in a couple of places? Something that will keep the paper in place but not permanently), and then trace the other cuts you'll need to make: the lens flange, self timer or strap lugs, screw heads, etc. Once the paper fits well, you can then use that as your pattern for whatever leather you're wanting to have as the final cover.
Another way to do this might be to use masking tape? (Preferably the type actually intended for masking paint as it is not as sticky.) I'd try to find some in a width that is wider than the camera body is tall so that you are using one piece. Tape around the body, then cut out the areas that need it. Carefully remove the tape so it doesn't deform, put it on the outside of your leather, cut to match.
I recovered a FED5 by using the paper pattern and it came out OK; if I could have found masking tape wide enough I'd have done it that way.
I know Cameraleahter sells some sheets of adhesive backed materials--and probably some sheets without adhesive--and you can really use anything that you like.
A sharp knife and lots of patience are the big requirements for this, I think.
It should be fairly straight forward to get the major dimensions--height and length--by simply measuring.
The tricky part will be sorting all the other cuts.
For those, I would start with a heavy kind of paper, cut out a rectangle that will cover the body, anchor that to the body (maybe rubber cement in a couple of places? Something that will keep the paper in place but not permanently), and then trace the other cuts you'll need to make: the lens flange, self timer or strap lugs, screw heads, etc. Once the paper fits well, you can then use that as your pattern for whatever leather you're wanting to have as the final cover.
Another way to do this might be to use masking tape? (Preferably the type actually intended for masking paint as it is not as sticky.) I'd try to find some in a width that is wider than the camera body is tall so that you are using one piece. Tape around the body, then cut out the areas that need it. Carefully remove the tape so it doesn't deform, put it on the outside of your leather, cut to match.
I recovered a FED5 by using the paper pattern and it came out OK; if I could have found masking tape wide enough I'd have done it that way.
I know Cameraleahter sells some sheets of adhesive backed materials--and probably some sheets without adhesive--and you can really use anything that you like.
A sharp knife and lots of patience are the big requirements for this, I think.
wolves3012
Veteran
You'll need to remove the lens-mount and innards from the shell first. Put the shell in an oven at about 200C, once hot you'll be able to scrape the vulcanite off with a blunt scraper. You'll probably need some re-heating as the shell cools fairly quickly. Stating the obvious but take care with the hot shell - gloves required! It's a bit of a messy job, I'm afraid.
EDIT: I'm pretty sure the Zorki C shell is the same as the Zorki 1 (d & e variants), for which I think there is a ready-cut leatherette available.
ZeissFan
Veteran
I like the masking tape idea. I would remove the old covering first.
The material that I used came frtom cameraleather and is self-adhesive.
The material that I used came frtom cameraleather and is self-adhesive.
kievan81
Member
I think the aki-asahi.com sell the leatherette for Zorki-1 which I assume is the same size and form as Zorki-C's leatherette
http://aki-asahi.com/store/html/zorki-1/d/index.php
http://aki-asahi.com/store/html/zorki-1/d/index.php